Zdravim ve spolek,

Zde je program na dnesek, zitrek a cast nedele, doufam, ze nektere body lidi zaujmou a pridaji se.

*** vyroba experimentalniho inkubatoru - chladice a ventilatory jiz mame, dnes chci koupit jeden ci dva peltier moduly, thermopaste a isolacni material na inkubatorovou bednu (doufejme PIR aluminium coating), dnes vecer a zitra to budem davat dohromady, zde je od kamarada design ktery chci plusminus nasledovat s vyjimkou pozice dveri, ktere jsou v jeho pripade optimalizovane pro lednicku/chlazeni, danou bednu priveze take na 30c3

http://design.aeonfarm.com/t/ark-reactor-experimental-incubator/2/20

Dve solid state relay nekdo nahodou nema - na spinani cca dvou 90W peltiers (pokud nekdo ma a prodal by dejte prosim vedet jak solid state relay to peltiery, usetrilo by mi to behani). Mozek a cidla davaji dohromady kluci v Holandsku a Nemecku, takze to bude predstaveno na 30c3 ci v Brmlabu pri nasi unorove navsteve

*** konstrukce pracovnich stolu - pokud se postesti, tak dnes koupime cca 200x60x2 cm omyvatelne a normalni drevotriskove desky; 4x4 a 4x2 cm sloupky a vetsi mnozstvi ocelovych profilu na spojeni materialu plus srouby a matky. Co je rozumnejsi Hornbach, OBI ci Baumax? Vsechno ma byt pospolu smerem na Ruzyn, kde bych to rad koupil abych nemusel moc jezdit. budeme v zasade replikovat toto

https://secure.flickr.com/photos/100090979@N05/9486081816/in/set-72157635018821063

na obrazku je 3 m verze, tu ale do haker busu nenarvu, takze 2-2.5 m max

*** fermenty - podle toho zda se nam podari poridit cca 20-30 l plastove fermentacni kyble a nakoupit suroviny,  by jsme fermentovali zaklad na zazvorovou limonadu, radi by jsme udelali par 2.5-3 l fermentu na styl Korejskeho kimchi, dle zajme by toto propuklo dnes ci zitra

Nuze takovy je plan, ozvete se kdo ma zajem se pridat.

Ahoj Frantisek

Frantisek Algoldor Apfelbeck

PS Kopie emailu od Larse

Hi all,

i dont have technical data of my peltiers. i measured 7,5a at 12v = 90w

for the two together. we got a temperature difference of 20° in our 94

liter box in the negative direction. peltiers can heat much better than

cool. the hexayurt material is much thicker than my BASF Styrodur 3035

CS i used. So 89 W peltier should work fine. i think a bit more or less

is ok. 267 W is too much. you cannot cool the hot side with a normal cpu

cooler, you need watercooling here.

your build is *much* to inefficient. try to use 2 cpu coolers with the

peltier between them. one cooler inside the box, one outside. fill every

hole with the insulating material. will the gap around the peltier

between the coolers, too. use a larger cooler, especially on on the outside.

https://www.dropbox.com/sh/cajqjeobtquhgwe/TOnLeklRlG

you can connect your electronics to the peltiers in mycooling box at the

congress and use it as an incubator prototype if you want.