Pokial sa rozhodnete pouzit pilight, tak venujte pozornost stranke s odporucaniami: http://wiki.pilight.org/doku.php/advice
Ale nic nieje nemozne :)
2014-03-18 10:05 GMT+01:00 Robert Vojcik robert@vojcik.net:
Ja neviem mozno ze to bude offtopic ak som nepochopil temu tak sa ospravedlnujem.
Ale ked som riesil ovladanie zasuviek na dialku najlepsim riesenim mi prislo kupit si 433 Mhz vysielac/prijimac z ebay alebo z ciny (investicia do 150 Kc). Napriklad: http://dx.com/p/433mhz-rf-transmitter-receiver-link-kit-green-221225
Nasledne som pouzival najlacnejsie spotrebice (zasuvky, vypinace, stmievace, cidla teploty) pracujuce na 433 Mhz (ceny tiez radovo v 100 korunach), maju ich vsade mozne.
Co sa tyka samotneho softveru nieje problem si to nabastlit pripadne vyuzit nieco hotove: http://www.pilight.org/
Z-wave a podobne mi prisli zbytocne drahe a obmedzujuce.
2014-03-18 9:07 GMT+01:00 Rado1 rado@rado1.cz:
Kedze sa chytili zatial len "nasi", budem pokracovat po nasom...
ZigBee (pripadne najrozsirenejsia implementacia XBee) ma zaujalo uz pred vyse rokom. Velky vyber modulov, dostupna dokumentacia pre koderov...
Kedze s jednocipakmi som sa naposledy hral pred 20 rokmi, tazko sa mi bude naskakovat naspat do tohoto vlaku. Hranie s *duinami ma zatial nelaka, tak isto hromadny nakup Rpi ku kazdej zasuvke.
Ked som hladal hotove vyrobky, pre ZigBee toho moc nie je a ked je, je to vacsinou pre amerikanske zasuvky.
Z-wave som tak akosi prehliadal, pretoze som bol zahackovany na ZigBee. Az som natrafil na tento produkt: http://www.fibaro.com/en/the-fibaro-system/wall-plug
Z mojho pohladu je to killer aplikacia, pretoze nemusim rozmontovavat ziadne zasuvky (aj ked to mi ziaden problem nerobi). Mozem zacat prakticky len s meranim spotreby 2-3 spotrebicov v domacnosti (a to je moj primarny ciel "home automation"). Ked som nasledne hladal veci okolo Z-wave, nasiel som aj ine vyrobky (spinace/stmievace do vypinacovych krabic, zasuviek, dverne snimace - dokonca kombinovane s inymi velicinami) a ich ponuka mi pride lepsia - hlavne pre nase europske nasadenie - ako u ZigBee. Dokonca aj USB riadiacich modulov kompatibilnych s Linuxom mi pride lepsia ponuka.
To, ze cipy vyraba jeden vendor - ano, pohladu "free world" - je zle a hnusne a kryptofasisticke, ale zasa mam vacsiu istotu, ze mi vyrobky viacerych vendorov budu spolupracovat (co u ZigBee vraj az taka samozrejmost nie je). Je mi jasne, ze si musim davat pozor, aby som kupil vyrobok s nasim RF pasmom.
Teraz mi vlastne ide len o to, ci som nahodou v tej zaplave hype prezentacii k Z-wave vyrobkom neprehliadol nieco, kvoli comu si neskor budem buchat hlavu o stenu (slabe sifrovanie, silne rusenie s TV a pod,...). Takze ma zaujimalo, ci uz niekto z vas nevychytal slepe cestu a usetrim mi cas, peniaze a nastvanost mojej manzelky. :-)))
Diky.
P.S. Som si spomenul, ze zatial ma zarazilo len jedno - v navodoch k Z-wave vyrobkom je vzdy parovanie riesenie ako: vytiahnut riadiaci USB kluc z PCdla/servra, zmacknut na nom tlacitko, zmacknut tlacitko na novom module a cakat, kym ledky neohlasia sparovanie. To neexistuje ziadne softverove discovery bez nutnosti downtime uz existujucej infrastruktury?
-- Rado1 rado (at) rado1.cz
On Mon, Mar 17, 2014 at 11:39:44PM +0100, Vitezslav.Zak wrote: #> Dne 17.3.2014 22:54, Ondrej Mikle napsal(a): #> >On 03/17/2014 11:28 AM, Rado1 wrote: #> >>Hi guys. #> >> #> >>Does anybody tried some of these protocols for home automation? #> >>I have read a lot of comparisons and don't know what way to go. #> >> #> >>I'm not good in HW development therefore I will not build my own devices. #> >>My plans are build existing devices, control them through some USB controller #> >>connected to my Linux home server. #> >We've bought few zigbee boards, they should have fairly large range. I don't #> >know about the Z-wave protocol. #> > #> >The zigbee boards' main problem was that they required some proprietary windows #> >utility to program them, which acutally does it via UART, so it's fairly simple #> >to sniff the commands. They may be already (unofficially) documented somewhere. #> > #> >Second problem was that the ones we got a fairly high failure rate (I think 2-3 #> >out of 5 simply refused to be programmed). Not sure if it was just bad luck. #> >Maybe I could find them somewhere and bring it to brm for testing. #> #> Some vendors sell devices with a proprietary sw layer on top of #> zigbee. Such devices might not work with others. #> #> Z-wave products *should* work flawlessly as any product marked as #> z-wave compatible has to be certified by z-wave alliance. There is #> a shield board for raspi, called RaZberry, this is what I'm #> planning to start with. #> #> V. #> #> _______________________________________________ #> Brmlab mailing list #> Brmlab@brmlab.cz #> http://brmlab.cz/cgi-bin/mailman/listinfo/brmlab _______________________________________________ Brmlab mailing list Brmlab@brmlab.cz http://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
-- *Róbert Vojčík* email: robert@vojcik.net XMPP: robert@vojcik.net