To be honest, we print at work from PETG, ASA and ABS without enclosure and without dryer (Prusa MK3). It was not much better with the enclosure... Way more influence is by the mode (e.g. adding stress relief slots, mouse ears to help with adhesion etc.)
Btw. you should probably take this discussion to brmlab@
On 31. 03. 23 14:27, Vasiliy Chernov via Rada wrote:
Hi Everyone,
I found today this box for 3D printer: https://www.majkl3d.cz/p/creality-kryt-na-3d-tiskarnu
It seems like a great solution for our printer. Relatively cheap and will allow to print different types of filament (not only PLA as it is today).
Also, I can order filament dryer. It is a bit more expensive on that website than on Aliexpress. So, if everybody is fine, we can order either just that one, or both.
What do you think? Cheers!
Rada mailing list Rada@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/rada
Fair point. Thanks!
On Fri 31. 3. 2023 at 17:16, Jan Hrach jenda@hrach.eu wrote:
To be honest, we print at work from PETG, ASA and ABS without enclosure and without dryer (Prusa MK3). It was not much better with the enclosure... Way more influence is by the mode (e.g. adding stress relief slots, mouse ears to help with adhesion etc.)
Btw. you should probably take this discussion to brmlab@
On 31. 03. 23 14:27, Vasiliy Chernov via Rada wrote:
Hi Everyone,
I found today this box for 3D printer: https://www.majkl3d.cz/p/creality-kryt-na-3d-tiskarnu
It seems like a great solution for our printer. Relatively cheap and
will allow to print different types of filament (not only PLA as it is today).
Also, I can order filament dryer. It is a bit more expensive on that
website than on Aliexpress. So, if everybody is fine, we can order either just that one, or both.
What do you think? Cheers!
Rada mailing list Rada@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/rada
-- Jan Hrach | https://jenda.hrach.eu/
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
I think not good point :)
In brmlab, specially in hwlab, you cant print anything from petg because printers are placed in "windy" place. If we can print from petg we need petg and box. I create on from paper but somewho trash it :).
I think we need few plates from acryl and make hard case from ikea lack.
If brm pay it, i build it :).
Rainbof
Dne pá 31. 3. 2023 17:43 uživatel Vasiliy Chernov tusk1237@gmail.com napsal:
Fair point. Thanks!
On Fri 31. 3. 2023 at 17:16, Jan Hrach jenda@hrach.eu wrote:
To be honest, we print at work from PETG, ASA and ABS without enclosure and without dryer (Prusa MK3). It was not much better with the enclosure... Way more influence is by the mode (e.g. adding stress relief slots, mouse ears to help with adhesion etc.)
Btw. you should probably take this discussion to brmlab@
On 31. 03. 23 14:27, Vasiliy Chernov via Rada wrote:
Hi Everyone,
I found today this box for 3D printer: https://www.majkl3d.cz/p/creality-kryt-na-3d-tiskarnu
It seems like a great solution for our printer. Relatively cheap and
will allow to print different types of filament (not only PLA as it is today).
Also, I can order filament dryer. It is a bit more expensive on that
website than on Aliexpress. So, if everybody is fine, we can order either just that one, or both.
What do you think? Cheers!
Rada mailing list Rada@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/rada
-- Jan Hrach | https://jenda.hrach.eu/
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
I have some acrylic sheets stashed in the lab. They probably have “Mat” written on them. Feel free to use them to make the box, just if you could please try to optimize for minimum waste that would be superb. There should me 3 sheets around 100-150cm in length, if I remember correctly we placed them next to some planks on the right side of the hardware lab.
On Fri 31. 3. 2023 at 18:44, Ondrej Beranek rainbof@gmail.com wrote:
I think not good point :)
In brmlab, specially in hwlab, you cant print anything from petg because printers are placed in "windy" place. If we can print from petg we need petg and box. I create on from paper but somewho trash it :).
I think we need few plates from acryl and make hard case from ikea lack.
If brm pay it, i build it :).
Rainbof
Dne pá 31. 3. 2023 17:43 uživatel Vasiliy Chernov tusk1237@gmail.com napsal:
Fair point. Thanks!
On Fri 31. 3. 2023 at 17:16, Jan Hrach jenda@hrach.eu wrote:
To be honest, we print at work from PETG, ASA and ABS without enclosure and without dryer (Prusa MK3). It was not much better with the enclosure... Way more influence is by the mode (e.g. adding stress relief slots, mouse ears to help with adhesion etc.)
Btw. you should probably take this discussion to brmlab@
On 31. 03. 23 14:27, Vasiliy Chernov via Rada wrote:
Hi Everyone,
I found today this box for 3D printer: https://www.majkl3d.cz/p/creality-kryt-na-3d-tiskarnu
It seems like a great solution for our printer. Relatively cheap and
will allow to print different types of filament (not only PLA as it is today).
Also, I can order filament dryer. It is a bit more expensive on that
website than on Aliexpress. So, if everybody is fine, we can order either just that one, or both.
What do you think? Cheers!
Rada mailing list Rada@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/rada
-- Jan Hrach | https://jenda.hrach.eu/
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
Just a reminder, there is a dormant 3d printer enclosure, built from IKEA STUVA. If you enter HW Lab, it's the white box on the floor on your left.
https://www.reddit.com/r/3Dprinting/comments/hfjbff/ikea_stuva_enclosure/
Perhaps it can be reused.
--cgi
On 31/03/2023 7:21 pm, Ondrej Beranek wrote:
I think not good point :)
In brmlab, specially in hwlab, you cant print anything from petg because printers are placed in "windy" place. If we can print from petg we need petg and box. I create on from paper but somewho trash it :).
I think we need few plates from acryl and make hard case from ikea lack.
If brm pay it, i build it :).
Rainbof
Dne pá 31. 3. 2023 17:43 uživatel Vasiliy Chernov tusk1237@gmail.com napsal:
Fair point. Thanks! On Fri 31. 3. 2023 at 17:16, Jan Hrach <jenda@hrach.eu> wrote: To be honest, we print at work from PETG, ASA and ABS without enclosure and without dryer (Prusa MK3). It was not much better with the enclosure... Way more influence is by the mode (e.g. adding stress relief slots, mouse ears to help with adhesion etc.) Btw. you should probably take this discussion to brmlab@ On 31. 03. 23 14:27, Vasiliy Chernov via Rada wrote: > Hi Everyone, > > I found today this box for 3D printer: > https://www.majkl3d.cz/p/creality-kryt-na-3d-tiskarnu > > It seems like a great solution for our printer. Relatively cheap and will allow to print different types of filament (not only PLA as it is today). > > Also, I can order filament dryer. It is a bit more expensive on that website than on Aliexpress. So, if everybody is fine, we can order either just that one, or both. > > What do you think? > Cheers! > > _______________________________________________ > Rada mailing list > Rada@brmlab.cz > https://brmlab.cz/cgi-bin/mailman/listinfo/rada -- Jan Hrach | https://jenda.hrach.eu/ _______________________________________________ Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab _______________________________________________ Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
Ooo! Stuva maybe will be good. I plan use 2x ikea lack (because our printers are little bit tall) tommorow i measure it and bring good spool of PLA.
rainbof.
so 1. 4. 2023 v 18:55 odesílatel Josef Šmidrkal via Brmlab brmlab@brmlab.cz napsal:
Just a reminder, there is a dormant 3d printer enclosure, built from IKEA STUVA. If you enter HW Lab, it's the white box on the floor on your left.
https://www.reddit.com/r/3Dprinting/comments/hfjbff/ikea_stuva_enclosure/
Perhaps it can be reused.
--cgi
On 31/03/2023 7:21 pm, Ondrej Beranek wrote:
I think not good point :)
In brmlab, specially in hwlab, you cant print anything from petg because printers are placed in "windy" place. If we can print from petg we need petg and box. I create on from paper but somewho trash it :).
I think we need few plates from acryl and make hard case from ikea lack.
If brm pay it, i build it :).
Rainbof
Dne pá 31. 3. 2023 17:43 uživatel Vasiliy Chernov tusk1237@gmail.com napsal:
Fair point. Thanks!
On Fri 31. 3. 2023 at 17:16, Jan Hrach jenda@hrach.eu wrote:
To be honest, we print at work from PETG, ASA and ABS without enclosure and without dryer (Prusa MK3). It was not much better with the enclosure... Way more influence is by the mode (e.g. adding stress relief slots, mouse ears to help with adhesion etc.)
Btw. you should probably take this discussion to brmlab@
On 31. 03. 23 14:27, Vasiliy Chernov via Rada wrote:
Hi Everyone,
I found today this box for 3D printer: https://www.majkl3d.cz/p/creality-kryt-na-3d-tiskarnu
It seems like a great solution for our printer. Relatively cheap and
will allow to print different types of filament (not only PLA as it is today).
Also, I can order filament dryer. It is a bit more expensive on that
website than on Aliexpress. So, if everybody is fine, we can order either just that one, or both.
What do you think? Cheers!
Rada mailing list Rada@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/rada
-- Jan Hrach | https://jenda.hrach.eu/
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
Brmlab mailing listBrmlab@brmlab.czhttps://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
-- Josef Smidrkal
Brmlab mailing list Brmlab@brmlab.cz https://brmlab.cz/cgi-bin/mailman/listinfo/brmlab
-
Jan Hrach -
Josef Šmidrkal -
Mateusz Sadowski -
Ondrej Beranek -
Vasiliy Chernov